Solidworks get write access macros

A stored series of commands and functions that can be run to perform a specific task or tasks. In Excel a macro could be a complete program.

Solidworks get write access macros

These tools are much more powerful than the techniques I discuss in the previous section. But along with power comes responsibility. Using the debugging tools takes a bit of setup work.

About Help

Setting breakpoints in your code In earlier sections, I discuss using MsgBox functions in your code to monitor the values of certain variables. Displaying a message box essentially halts your code in mid-execution, and clicking the OK button resumes execution.

You can set a breakpoint in your VBA code in several ways: Move the cursor to the statement at which you want execution to stop; then press F9. Click in the gray margin to the left of the statement at which you want execution to stop. This is I used mainly.

Position the insertion point in the statement at which you want execution to stop. The results of setting a breakpoint are shown in below figure.

VBE highlights solidworks get write access macros line to remind you that you set a breakpoint there; it also inserts a large dot in the gray margin. When you execute the procedure, VBE goes into Break mode before the line with the breakpoint is executed.

In Break mode, the word [break] is displayed in the VBE title bar. To quickly remove a breakpoint, click the large dot in the gray margin or move the cursor to the highlighted line and press F9.

What is Break mode? You can think of it as a state of suspended animation. Your VBA code stops running and the current statement is highlighted in bright yellow. Press F8 to step through your code one line at a time to check various things while the program is paused.

Move the mouse pointer over a variable to display its value in a small pop-up window. Skip the next statement s and continue execution there or even go back a couple of statements.

Edit a statement and then continue. Below figure shows some debugging action. In Break mode, the Immediate window is particularly useful for finding the current value of any variable in your program.

For example, if you want to know the current value of a variable, enter the following in the Immediate window and press Enter. The Immediate window lets you do other things besides check variable values. For example, you can change the value of a variable, try for a new condition.

Just make sure that the command you enter is a valid VBA statement. Stepping through your code While in Break mode, you can also step through your code line by line. One statement is executed each time you press F8 Throughout this line-by-line execution of your code, you can activate the Immediate window at any time to check the status of your variables.

You can use your mouse to change which statement VBA will execute next. If you put your mouse pointer in the gray margin to the left of the currently highlighted statement which will usually be yellowyour pointer changes to a right-pointing arrow.

Simply drag your mouse to the statement you want to be done next and watch that statement turn yellow. Using the Watch window In some cases, you may want to know whether a certain variable or expression takes on a particular value.

For example, suppose that a procedure loops through 1, times.

solidworks get write access macros

You notice that a problem occurs during the th iteration of the loop. Well, you could insert a breakpoint in the loop, but that would mean responding to prompts before the code finally get to the iteration you want to see and that gets boring real fast.

A more efficient solution involves setting a watch expression. The Add Watch dialog has three parts: Enter a valid VBA expression or a variable here. Select the procedure and the module you want to watch. Note that you can select All Procedures and All Modules. Select the type of watch by clicking an option button.

Your choice here depends on the expression you enter.Jul 05,  · Hi, Im wondering if i can use a macro so when a Menu Button is pressed it adds the current date to the currently selected cell?

Ive tried using Now() and assigning it to the Properties of the menu button ive made but it doesnt work. SOLIDWORKS APPS (Macro) Library The SOLIDWORKS APPS library is a collection of macros (programs) developed by Solid Solutions to help our customers speed up the design process and reduce the overhead of executing repetitive tasks.

Jan 15,  · I put this down to macro security settings), or the macros are not included at all, not even the button in the access bar. It does not go systematically wrong, because for some users, everything works great. To convert your temporary or trial key to regular long-term keys, you need to request a new license key file.

Generate the request form on the machine that will be running SmartCAM, as returned license key file will be tied directly to this computer.

A Review: Embedded System for Dynamic Location based Advertisement using Google Maps API. Discover our Frequently Asked Questions relating to SOLIDWORKS installation.

Born To Design | Tips & Demos | SolidWorks